![]() |
Components for Si-WaveBackgroundThe ANF 2.0 specification (which is the version written by NETEX-G and NETEX-O) does not include descriptions of components such as resistors, capacitors, inductors, active devices or transformers. So if you are converting a PCB into ANF for use with SI-Wave you must manually add this information in after the conversion. The Ansoft component file is used together with the Ansoft Neutral Format (ANF) version 2 to define the location and electrical properties of components in a printed circuit board. References to net number, layer number, padstack number, and geometrical coordinates must be consistent with information defined in the ANF file. The format for the *.cmp file is shown below. "X" lines specify pin parameters.
X <net #>
<start layer #> <end layer #>
<padstack #> <x> <y> <angle in degrees>
<part number>
<reference designator>
<pin number>
The net #, layer #s and padstack # correspond to values defined for nets, layers and padstacks in the ANF V2. |
|
Example 1 B_RES "R28" "CC0603" X 1 2 2 48 -3382.000000 -1650.000000 0.000000 CC0603 R28 2 X 438 2 2 48 -3318.000000 -1650.000000 0.000000 CC0603 R28 1 "???" "???" "???" "???" E_RES The four �???� strings at the end of each record in the CMP file are placeholders for the nominal element value, the parasitic capacitance, the parasitic inductance and parasitic resistance, respectively. Set to �???� if these values are unknown. Example 2 B_CAP C54 CC0603 X 2 2 2 48 2257.000000 -900.000000 180.000000 CC0603 C54 2 X 266 2 2 48 2193.000000 -900.000000 180.000000 CC0603 C54 1 10n 0 1n 0.2 E_CAP The record above defines a capacitor with a nominal value of 10nF, a parasitic inductance of 1nH and a parasitic resistance of 0.2ohms. Example 3 B_IND "L26" "CC1206"
X 226 2 2 21 -1275.000000 -391.000000 90.000000 CC1206 L26 2
X 223 2 2 21 -1275.000000 -259.000000 90.000000 CC1206 L26 1
"???" "???" "???" "???"
E_IND
Example 4
B_IC "D21" "1N5822"
X 356 2 12 2 2550.000000 -1050.000000 90.000000 1N5822 D21 1
X 2 2 12 2 2550.000000 -450.000000 90.000000 1N5822 D21 2
"???" "???" "???" "???"
E_IC
Any active or semiconductor device (in this case a diode) is classfied as an IC. Example 5
B_IO "SW1" "SW_6PDT_RA"
X 198 2 12 19 -905.950000 1276.300000 0.000000 SW_6PDT_RA SW1 16
X 206 2 12 19 -905.950000 1176.300000 0.000000 SW_6PDT_RA SW1 17
X 201 2 12 19 -905.950000 1076.300000 0.000000 SW_6PDT_RA SW1 18
X 0 2 12 19 -905.950000 1576.300000 0.000000 SW_6PDT_RA SW1 13
X 0 2 12 19 -905.950000 1476.300000 0.000000 SW_6PDT_RA SW1 14
X 0 2 12 19 -905.950000 1376.300000 0.000000 SW_6PDT_RA SW1 15
X 0 2 12 19 -905.950000 1876.300000 0.000000 SW_6PDT_RA SW1 10
X 0 2 12 19 -905.950000 1776.300000 0.000000 SW_6PDT_RA SW1 11
X 0 2 12 19 -905.950000 1676.300000 0.000000 SW_6PDT_RA SW1 12
X 199 2 12 19 -805.950000 1076.300000 0.000000 SW_6PDT_RA SW1 9
X 205 2 12 19 -805.950000 1176.300000 0.000000 SW_6PDT_RA SW1 8
X 197 2 12 19 -805.950000 1276.300000 0.000000 SW_6PDT_RA SW1 7
X 197 2 12 19 -805.950000 1376.300000 0.000000 SW_6PDT_RA SW1 6
X 207 2 12 19 -805.950000 1476.300000 0.000000 SW_6PDT_RA SW1 5
X 199 2 12 19 -805.950000 1576.300000 0.000000 SW_6PDT_RA SW1 4
X 198 2 12 19 -805.950000 1676.300000 0.000000 SW_6PDT_RA SW1 3
X 208 2 12 19 -805.950000 1776.300000 0.000000 SW_6PDT_RA SW1 2
X 201 2 12 19 -805.950000 1876.300000 0.000000 SW_6PDT_RA SW1 1
"???" "???" "???" "???"
E_IO
Connectors and other passive devices such as switches are classified as IO. |
Download |
Benchmark Files |
Revision History |
Price |